Toroidal transformer core provider right now? Nanocrystalline core is getting more and more popular in the electronic and electrical industries, for its high electrical performances. Our features nanocrystalline core material products are Nanocrystalline Common mode choke cores and Nanocrystalline Current Transformer cores. Read additional information on transformer core manufacturers. Soft magnetic materials are those materials that are easily magnetised and demagnetised. They typically have intrinsic coercivity less than 1000 Am-1. They are used primarily to enhance and/or channel the flux produced by an electric current. The main parameter, often used as a figure of merit for soft magnetic materials, is the relative permeability (µr, where µr = B/ µoH), which is a measure of how readily the material responds to the applied magnetic field. The other main parameters of interest are the coercivity, the saturation magnetisation and the electrical conductivity.

We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Hysteresis loss is the iron loss caused by the hysteresis phenomenon in the magnetization process of the iron core. The size of this loss is directly proportional to the area surrounded by the hysteresis loop of the material. The hysteresis loop of silicon steel is narrow, and the hysteresis loss of transformer core made of silicon steel is small, which can greatly reduce its heating degree.

This is because the sheet iron core can reduce another iron loss – “eddy current loss”. When the transformer works, there is alternating current in the coil, and the magnetic flux generated by it is of course alternating. This changing magnetic flux produces an induced current in the iron core. The induced current generated in the iron core flows in a ring in a plane perpendicular to the magnetic flux direction, so it is called eddy current. Eddy current losses also heat the core. In order to reduce the eddy current loss, the iron core of the transformer is stacked with silicon steel sheets insulated from each other, so that the eddy current passes through a small section in the narrow and long circuit, so as to increase the resistance on the eddy current path; At the same time, the silicon in silicon steel increases the resistivity of the material and reduces the eddy current. rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size.

Amorphous Core is preferred choice for transformers required low losses at high frequency. We have amorphous c-cores,amorphous ribbon cores,amorphous cut cores,amorphous core transformers . Please find out more about crgo core material. There are 50% and 80% nickel iron materials available, in which we manufactures Mumetal Toroidal core and Mumetal C-core, for the applications in high quality Current Transformers and power supplies industries. Find extra information on https://www.transmart.net/.

However, at the same BM, the loss of Fe based amorphous alloy is smaller than that of 0.23mm thick 3% silicon steel. It is generally believed that the reason for low loss is the thin thickness and high resistivity of iron-based amorphous alloy strip. This is only one aspect. The main reason is that the iron-based amorphous alloy is amorphous, the atomic arrangement is random, there is no magnetocrystalline anisotropy caused by atomic directional arrangement, and there is no grain boundary causing local deformation and composition offset. Therefore, the energy barrier hindering domain wall motion and magnetic moment rotation is very small, with unprecedented soft magnetism, so it has high permeability, low coercivity and low loss.

On the one hand, it can isolate eddy current, and the data is suitable for higher frequencies; On the other hand, due to the gap effect between particles, the data has low permeability and constant permeability; Because the particle size is small, there is basically no skin phenomenon, and the change of permeability with frequency is relatively stable; Moreover, the powder core can be prepared into special-shaped parts of various shapes for different fields; Finally, the damaged strip in industry can be crushed into magnetic powder, and then made into magnetic powder core, which can reduce the loss and improve the use value of data. The magnetoelectric properties of magnetic particle core mainly depend on the permeability of powder material, size and shape of powder, filling coefficient, content of insulating medium, forming pressure and heat treatment process.