Top rated o ring provider? We can design the suitable spring energized seals for your application. Our oil seals have TC, TB, SC, DC, TCV and so on. Looking forward to supply the best seals for you.(O Ring Manufacturers & Hydraulic Oil Seal Manufacturers). DMS SEALS, the seals manufacturer, was founded in 2008. DMS started by manufacturing filled PTFE seals, including bronze filled PTFE, carbon filled PTFE, graphite PTFE, MoS2 filled PTFE, and glass filled PTFE. We now also produce O-rings made of NBR, FKM, silicone, EPDM, FFKM. Find more details on o ring supplier.
The O-ring seal, which is also called shaft seal, is noted for a reasonable compression and stretch rate to achieve a good sealing effect. It will not leak when it is sealed statically. At the same time, the O-ring size is properly matched to the groove size. The structure is simple and its installation is very close to the machine. Its most prominent advantage is its self-sealing effect, eliminating the need for periodic adjustments. We guarantee that the size and mounting grooves of all our O-rings are standardized, so they are cost-effective and easy to maintain. They have low frictional resistance and are suitable for occasions where the pressure is often alternating.
It can maintain stable performance after prolonged exposure to various corrosive compounds. Due to its lack of polarity, low unsaturation, and high chemical stability, our gasket has high resistance to various polar chemicals such as alcohols, acids (acetic acid, hydrochloric acid, etc.), strong base (sodium hydroxide, oxidant, hydrogen peroxide), detergents, animal and vegetable oils, ketones and certain esters. It is designed to have excellent aging resistance and excellent resistance to compression set and compression stress relaxation. Therefore, our gasket has significant advantages over other conventional gaskets. Its excellent materials and manufacturing process enables it to achieve effective sealing when exposed to corrosive chemicals, friction, high temperatures or very low temperatures. At the same time, it is easy to install and has industry-leading creep resistance, which saves users a lot of time and cost and increases productivity.
Since the scraper seal is made of the special material, PTFE, it has an impurity immersion function. Therefore, when combined with the piston rod seal and the metal bushing, it can prevent damage to the piston rod and prevent the accumulation of oil pressure. It has a diameter range of 3-1600mm and a temperature range of -30°C + 200°C. The wiper scraper seal can operate at speeds of up to 5 m/s. It has high wear resistance, tear resistance, low-temperature resistance and good strength. Our wiper seals can be used in combination with piston seals and anti-wear rings to prevent oil in the cylinder from being mixed with foreign matter, which causes damage to the working seal. It is especially suitable for piston rods with a large diameter. Moreover, it has a wide range of applications, such as agricultural machinery, injection moulding machines, forklifts, cranes and so on.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Discover more info at https://www.dmsseals.com/.